OLICOM, INC. OC-3232 Card Type Modem (synchronous/asynchronous), Token Ring Modem Chipset Rockwell RC288ACL Network Chipset Texas Instruments TMS380C30 Maximum Onboard Memory 160KB RAM/128KB Flash ROM Boot ROM Not available Network Transfer Rate 4Mbps/16Mbps Topology Ring Wire Type Shielded/Unshielded twisted pair Maximum Data Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC Fax Modulation Unidentified Error Correction/Compression MNP5, MNP10EC, V.42, V.42bis Fax Class Class I & II Data Bus PCMCIA Type II 53760 SUPPORTED STANDARD COMMANDS Basic AT Commands +++, ‘comma’, A/ A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z &C, &D, &F, &G, &K, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \G, \J, \K, \L, \N, \V %C, %E, %L, %Q Special AT Commands :E, -K, @M, +MS S-Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S12, S18, S24, S25, S26, S29, S30, S32, S33 S36, S38, S39, S46, S48, S82, S86, S91, S92, S95, S201 Note: See MHI help file for complete information. UNIDENTIFIED COMMANDS Command Default S14 Unidentified S16 Unidentified S21 Unidentified S22 Unidentified S23 Unidentified S27 Unidentified S28 Unidentified S31 Unidentified S37 Unidentified S40 Unidentified S41 Unidentified S80 Unidentified Proprietary AT Command Set AUTOSYNC OPTIONS Type: Register Format AT [cmds] S19=n [cmds] Default: 26 Range: 0 - 30 Description: Controls AutoSync protocol, HDLC address detection, bit coding type, and HDLC idle. Bit Value Function 0 0 Not used 1 0 Binary synchronous protocol used. 1 HDLC protocol used. 2 0 HDLC address detection disabled. 1 HDLC address detection enabled. 3 0 NRZI bit coding used. 1 NRZ bit coding used. 4 0 HDLC idle sends MARK. 1 HDLC idle sends FLAG or SYNC. AUTOSYNC HDLC ADDRESS Type: Register Format: AT [cmds] S20=n [cmds] Default: 0 Range: 0-255 Unit: Unidentified Description: Sets the HDLC address and binary synchronous character. CELLULAR STATUS INDICATOR Format: AT [cmds] ^T6 [cmds] Default: Read-only Range: 0-255 Description: Indicates the status of cellular phone. Bit Value Function 0 0 Cellular phone is not receiving a call. 1 Cellular phone is receiving a call. 1 0 Cellular phone is not in use. 1 Cellular phone is in use. 2 0 Cellular phone is not locked. 1 Cellular phone is locked. 3 0 Cellular service detected. 1 Cellular service not detected. 4 0 Cellular phone is powered off. 1 Cellular phone is powered on. 5 0 Cellular driver is initialized. 1 Cellular driver is not initialized. 6 0 Not used. 7 0 Cellular cable not detected. 1 Cellular cable detected. COUNTRY CODE Type: Configuration Format: AT [cmds] *NCnn [cmds] Description: Sets the modem's country code. The values and associated meanings for this command are unidentified. DIAL Type: Immediate Format: AT [cmds] D<#>;[cmds] Description: Dials the telephone number indicated according to any modifiers included in the string. Command Function DJ MNP10 link will be negotiated at 1200bps for this call. DK MNP10 power level adjustment enabled for this call. DL Re-dial last number. DP Pulse dialing enabled. DR Answer mode enabled; originate mode disabled following handshake initiation. DS=n Dial stored telephone number n. DT Tone dialing enabled. DW Dialing resumed following dial tone detection. D, Dialing paused for amount of time specified in S8 register. D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. DIAL (CON'T) Command Function D@ Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D^ Calling tone disabled for this call. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. DISPLAY BLACKLISTED NUMBERS Type: Immediate Format: AT [cmds] *B [cmds] Description: Displays the list of all blacklisted numbers and their statuses. DISPLAY CELLULAR DRIVER Type: Immediate Format: AT [cmds] ^I [cmds] Description: Displays cellular phone driver information. DISPLAY DELAYED NUMBERS Type: Immediate Format: AT [cmds] *D [cmds] Description: Displays the list of all delayed numbers and their statuses. DISPLAY INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested about the modem. Command Function I0 Displays product identification code. I1 Displays ROM checksum. I2 Tests and displays ROM checksum result. I3 Displays firmware revision. I5 Displays country code. DISPLAY STORED NUMBERS Type: Immediate Format: AT [cmds] \F [cmds] Description: Displays all stored telephone numbers. DOWNLOAD CELLULAR DRIVER Type: Immediate Format: AT [cmds] ^C2 [cmds] Description: Download cellular phone driver. PULSE DIALING MODE Type: Configuration Format: AT [cmds] *Zn [cmds] Description: Selects the type of pulse dialing the modem will use. Command Function *Z0 Modem will use pulse dialing type 0. *Z1 Modem will use pulse dialing type 1. REMOTE CONFIGURATION CHARACTER Type: Register Format: AT [cmds] S202=n [cmds] Default: Unidentified Range: Unidentified Unit: 1 ASCII character Description: Defines the character that, when sent four times within the guard time set by S12, will notify the remote modem that a remote configuration session has been requested.